To begin to draw a map of your ancestor’s land similar to the sketches made by the surveyors, you first need to understand the “code”.

Let’s use an example:  S 30 E 74 poles.  There are 3 pieces of information here.

  1. The 2 letters indicate the direction.  In this example, we will be measuring a line SE from a location.  If only 1 letter is given, then the direction is directly North, South, East or West.  For example:  E 17 poles will be a line drawn directly east.
  2. The number between the 2 letters indicates a number of degrees.  So we will be drawing a line that is 30o in the SE direction.
  3. The final number gives the length.  74 poles.

1 pole represents 16.5 feet, but for easy measuring, I made 1 pole equal to 1 mm on my ruler. (Millimeters are the tiniest marks on the metric ruler.  The numbers are for centimeters.)

When measuring the direction of your line, it is important to know that there are 2 locations for zero degrees – directly North and directly South. As you move toward the East or the West, the numbers get larger until you reach 90o.

You can measure your degrees with a regular protractor from the school supply section of your local store.  Measuring is much easier if you have a round protractor, which you can pick up at most office supply stores, but even those can be confusing because they are made to measure a full 360o going clockwise OR counterclockwise, so there are 2 different scales and you must be sure to use the correct one.

Because textbooks don’t lie flat, I’ve always made copies of the circular protractors on flexible, overhead transparency material that my students cut out and use to measure bearings in Geometry class. Because they are transparent, it’s easier to make sure you are lining things up correctly. So I used PhotoShop to create my own “surveying compass” that had only the necessary compass readings for the metes and bounds and I plan to copy it onto transparency material.  You can use the paper version as long as you hole punch the center of the  to make sure that the point you are measuring from lines up correctly. Since most people won’t have access to overhead projector film, I’ll make my illustrations with the paper version.

To draw  your map:

  1. It would be nice if every surveyor measured the property in a clockwise direction starting in the NE corner, or something like that, but they didn’t.  Until you get the hang of reading these codes, it can be difficult to know where to begin on your sheet of paper.  All I can say is that eventually, you’ll be able to read through the measurements and make a super quick sketch to at least see which direction they moved while measuring.
  2. Choose a point to begin your map.  You map will be similar to a dot-to-dot diagram, but you will not know where the next dot belongs until you draw a line.
  3. Lay the protractor center on the dot that will be your beginning.  Make sure that “N” is pointed straight up.  (Using graph paper makes this much easier.)
  4. Use the letters in “the code” to know which quarter of the protractor you’ll be using.  Make a small mark that lines up with the number of degrees which appears between the 2 letters.
  5. Using the metric side of your ruler, line up the 2 dots that you have made.  Measure from the original dot the number of millimeters that appears at the end of “the code”. (You can barely see my little pencil mark across from the #4 on the ruler in the next photo.) I write the code along this line so I can make sure I don’t skip any.
  6. The end of your line becomes the dot that goes in the middle of your compass for the next section of your boundary description.
  7. Continue around until you get back to the beginning.

MOST of the maps that I’ve completed with this method have come right back to the original dot that I had made.  But on a couple of them, they do not.  I have to believe that dragging chains up and down hills and around trees had to make these surveys less than perfect and after double checking my measurements, I chose to fudge my drawings just a bit when this happens to make them align – but I make a note that I’ve done that.

As I go through the deed, I also add information like owners of neighboring properties or landmarks that could still be around today – like river banks or creeks.  Those creeks are what have allowed me to pinpoint my ancestor’s location on maps.  I can also convert those poles into feet or miles to help me have a better idea of the size of my ancestor’s property.

After I complete the graph paper version, I cut it out and transfer it to cardstock and write all of the information that I know about the piece of property.

As I’m working my way through various deeds, I’m discovering neighbors and even can see a pattern of how my ancestor expanded his property. For example, after completing my maps from two different deeds, I found that the pieces of land were connected to each other.  Something I never would have figured out without paying attention to the details found in that frustrating metes and bounds code!

If you are researching in Kentucky and are looking for some highly detailed county maps, this web site has great maps from 1950 and 1999.

http://ukcc.uky.edu/maps/

My husband says you have to be a real math geek to spend a Saturday afternoon with a protractor drawing maps like this, but I’ll let you be the judge of that!

BONUS!  If you’ve stuck with me through this entire post, I have a gift for you! If you send me a SASE, I’ll mail you my compass printed on overhead material and I’ll even cut it out with my circle cutter!  Email me at lvonlanken [at] msn [dot] com and I’ll send you my snail mail addy! When I print my own compass tomorrow, I’ll print several overheads with 6 to a sheet so I’ll have plenty to share!

About these ads